Precision CNC machined aluminum tool for the installation and removal of 12-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8" drive. - 46mm 12-notch OD cup - Race Face® Cinch™, Rotor® BSA30, Zipp® Vuma™, Hawk Racing™ BB3086™, and more
$25.95 - $32.95
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their centering pilots demonstrate their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size pilot: - 49.8mm (for 1.5-inch standard): The 767 is used with the HTR-1 (HTR-1B) and 690XL facer to perform facing only. It fits head tubes with an inside diameter of 49.8mm (1.5" standard). - 43.8mm (for ZS44 and EC44): The 768 Pilot is used with the HTR-1 (HTR-1B), the 750 Centering Cone Adaptor and 690XL facer to perform facing only. It fits head tubes designed for low profile or, “zero-stack,” headsets. These head tubes have nominal inside diameters of 43.9mm. - 55.9mm (for internal 1.5-inch ZS): The 790 Pilot takes the place of the 789 Reamer when performing head tube facing only. The 790 is used with the HTR-1 Headtube Reamer, the 690-XXL Facing Cutter, and the 750.2 Centering Cone Adaptor. The tool allows facing head tubes with 55.95 – 55.90mm I.D. (“Internal” 1-1/2” ZS standard).
$9.95 - $11.95
Park Tool is world-renowned for their bicycle industry tools, and their pumps are no exception. Keep yours up to speed and working smoothly with these rebuild kits. - 1096K: Contains one #1081 head as well as one #1075 plunger gasket for older PFP-2 and first generation PFP-4 floor pumps. Also compatible with second-generation PFP-4 floor pumps. - 1096X: Contains one #1096R head, one #1472 fitting, and one #1075 plunger gasket for second generation PFP-4 floor pumps. Also compatible with PFP-2 and first-generation PFP-4 floor pumps. - 1096Z: Contains one #1096R head, one #1472 fitting, and one #1087 plunger gasket for PFP-5 and PFP-7 floor pumps. Also compatible with PFP-3, PFP-6, and PFP-8 floor pumps.
This is a single replacement pin for Park Tool HCW-4 and SPA-6 pin spanner wrenches.
Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.
$116.95 - $173.95
Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.
All metal cup made of 304 Stainless Steel.
Dial Indicator Set bolts directly to the DT-3 allowing for greater accuracy and a way to measure results. Now includes an elongated, cylindrical tip that is large enough to work around voids in most rotors.
$29.95 - $86.95
Frame and Fork Taps will become a lifesaver at some time for virtually every mechanic. These taps are made of high-carbon steel and are precision ground. Park Tool Frame and Fork Taps cut easily and fit conventional tap handles.
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
$6.49 - $11.49
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip.
The Park Tool FR-5.2GT is designed specifically for use when removing and installing cassette lockrings from thru axle hubs. -Utilizes a 12mm guide pin to stabilize the tool during use - Fits 12-spline cassette lockrings from Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and others (23.5mm diameter) - Fits some Shimano and similar disc brake rotor lockrings
Precision component screwdriver machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined and hard anodized 6061 aluminum handle.
Securely holds the TS-4 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
$9.95 - $14.95
World-famous Park Tool quality wrapped up in a combination metric wrench. Features both open and 12-point two-way ratcheting box ends. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful!
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. The MWR-SET includes 6mm to 17mm wrenches with a 12-point two-way ratcheting box end. Forged from chrome vanadium steel, chrome-plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful! - Includes 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, and 17mm wrenches
Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.
Park's Hydraulic Brake Piston Press is used to set or reset the piston(s) inside hydraulic disc brake calipers during installation, maintenance and repair. Just push it into the caliper to wedge the piston into place. It's made of tough tool steel with a comfortable and oversize rubber handle for a great grip.
The RT-1 Head Cup Remover makes headset cup removal easy. The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup. • Fits 1”, 1-1/8” and 1-1/4” headsets • Strong, heat treated alloy steel with nickel finish The RT-1 will also remove the PressFit 30 (PF30) bottom bracket units. The PressFit 30 inside diameter is the same as headset cups, and are pressed in the same manner. SHIS terminology: Removes cups of EC29, EC30, EC34, EC44, ZS41, and ZS44
Park Tool's Bottom Bracket Facing Set is designed to be a complete self-contained facing set, combining top-quality precision parts with ease of use. Simply install the threaded inserts using the facer handle, then insert the facing tool through the guides and install the tension spring and speed nut. After applying a liberal amount of cutting oil, the BFS-1 easily cuts the shell material, giving you a clean, faced surface. Now you're ready to install the bottom bracket. The English threading inserts are included. The Italian threading (36 x 24) inserts are available as an accessory, as part #688. Two are required.
Park's Chainring Nut Wrench makes chainring bolt installation and removal easy. It securely holds the slotted nut to prevent spinning when tightening or loosening the bolt. And, it's double-ended to fit most slotted-type nuts, including Campagnolo chainring bolt nuts.
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Park's Tire Seating Tool is designed to quickly seat the bead on stubborn tires. During inflation some tire beads can slip below the rim edge and become difficult to pull out and align. The PTS-1 comes to the rescue with its non-slip jaws and vinyl-coated handles that provide plenty of leverage for pulling out the tire. Plus, it's adjustable to fit various tire widths.
The Handlebar Holder prevents the handlebars and front wheel from swinging to the side and banging into the frame when your bike is mounted in a repair stand. It fits handlebars up to 32mm and all frame tubes up to 50mm in diameter, so it works on almost any road or mountain bike and is sure to make every repair easier.
The CRS-15EXT includes a tube and fitting to extend any CRS-15 to work on fork steering tubes up to 425mm.
Park Tool's versatile and durable 8oz Shop Hammer is a perfectly balanced striking instrument built for a wide variety of shop uses. - Forged steel, precision machined striking face - Non marring, replaceable composite tip - Fiberglass shaft with soft touch grip - 8oz (225g) Head - Length: 12" (30.5cm) - Steel striking face: 1" (25mm) diameter - Plastic face: 1-1/4" (32mm) diameter - Replacement tip: Part #293-8
A great way to start a tool collection! The perfect combination of tools to help the novice home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-3 includes more than 15 genuine Park Tool products plus a custom Park Tool toolbox. The SK-3 includes: AWS-11 Fold-Up Hex Wrench Set CC-3.2 Chain Checker CN-10 Professional Cable and Housing Cutter CT-5 Mini ChainBrute Chain Tool GP-2 Pre-Glued Super Patch Kit GSC-1 GearClean Brush MLP-1.2 Master Link Pliers PW-5 Pedal Wrench SD-2 Shop Screwdriver: #2 Phillips SW-7.2 Triple Spoke Wrench TL-1.2 Tire Lever Set #1622 Torx Compatible "L" Wrench
Precision CNC machined dual-sided aluminum tool for the installation and removal of 12- and 36-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. Fits Praxis M30 and M35 - M30: 12-notch 48mm OD cup - M35: 36-notch 51.7mm OD cup
The MTC-40 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along. - 2.5, 3, 4, 5, 6 and 8mm hex wrenches - T25 & T30 Torx compatible driver - Combo cross/straight tip screwdriver - 5- to 12-speed compatible chain tool* - Rotor straightener - CO2 cartridge inflator adaptor - Bottle opener - Key ring holder - Weight: 217g (7.65 ounces) *The MTC-40 chain tool will not peen Campagnolo 11-speed chain rivets (see CT-4.3 or CT-6.3)
The CC-4 is a drop-in style gauge that measures bicycle chain wear. The laser cut CC-4 accurately measures a long section of chain and strategically comes in contact with the chain in three places, quickly and easily taking the guesswork out of knowing when chain replacement is necessary. A worn chain will cause poor shifting as well as accelerate drivetrain wear. The tool works on any 5 to 12-speed derailleur chain (including SRAM AXS) and is designed to accurately indicate when a chain reaches .5% and .75% wear, the points at which most chain manufacturers suggest replacement.